- Minimum quantity should 5 of "Chip Resistor – Surface Mount 150 Ohm 1% (1/8W) 0805 SMD"
-
-
-
6V 2400RPM DC MOTOR
- Rotation: CCW
- Rated Speed: 2400RPM
- RPM-Rated voltage: DC 6V
- Thread hole diameter: 2mm/0.08″
- Shaft size: 6 x 2mm / 0.24″ x 0.08″(H*D)
- Body size (Not include shaft): 34 x 25mm / 1.3″ x 18″(D*H)
-
LKR18.00LKR24.00Male 40Pin Header Right Angle 2.54mm
LKR18.00LKR24.00 -
FDS6675 30V 11A P-Channel MOSFET (SOIC-8) – SMD
TI LM2596S-3.3 TO-263 DC-DC Switching Converters
LKR78.00LKR84.00FDS6675 30V 11A P-Channel MOSFET (SOIC-8) – SMD
LKR78.00LKR84.00 -
LM2596-3.3 SWITCHING REGULATOR
TI LM2596S-3.3 TO-263 DC-DC Switching Converters
-
MB102 Breadboard Power Supply Module 3.3V/5V
MB102 Breadboard Power Supply Module 3.3V/5V
The MB102 Breadboard Power Supply Module 3.3V/5V securely fits in a standard 400 or 800 tie points breadboard it also features reverse polarity protection, the module can take 6.5V to 12V input and can produce 3.3V and +5V. The module can also output 5V on USB connector or input through USB connector. It’s a must have product for experimenters those have to test/prototype electronic circuits on breadboard
Features
- Breadboard power supply module, with 5 V, 3.3 V output voltages
- Apply to MB102 Standard breadboard
- Input voltage: 6.5-12 V (DC) or 5V USB power supply
- Output voltage: 3.3V and 5V can switch over
- Maximum output current: <700 ma
- Input voltage ON/OFF switch
- Independent control of upper and Lower Bread Board Power Rails. Can switch over to 0 V, 3.3 V, 5 V using jumpers on any rail.
- On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use.
LKR210.00 -
TCS230 Color Recognition Sensor module
TCS230 Color Recognition Sensor Module for arduino c80
- Chip:tcs230
- Input voltage: DC 3V-5V
- Output frequency voltage: 0 ~ 5V
- Use bright white LED lights
- can be connected directly with Microcontroller
- Static detection of the measured object color
- Best detection distance: 10mm
-
DSO Nano
Features
-
Portable and lightweight
-
Color display
-
Waveform storage and playback
-
6 triggering modes
-
200Khz Analog Bandwidth
-
Complete measurement markers and signal characteristics
-
Built-in Signal Generator
-
Accessories available
-
Open Source
Technical details
Dimensions 149mm x101mm x33mm Weight G.W 184g Battery Lithium Cells / Batteries contained in equipment UN3481 – PI967 Display 2.8” color TFT LCD Display Resolution 320×240 Display Colors 65K Analog Broadband 0 ~ 200kHz Max. Sampling Rate 1Msps 12 bit Sampling Storage Depth 4096 points Transverse Sensitivity 1uS/Div~10S/Div(1-2-5 stepping) Vertical Sensitivity 10mv/Div~10V/Div(x1 probe) 0.5V/Div~10V/Div(x10 probe) Input Resistance >500KΩ Max. Input Voltage 40Vpp（x1 probe） Coupling Mode DC Triggering Mode Auto，Normal，Single，None Auto Measurement Frequency, cycle, duty, Vpp, Vram, Vavg, DC voltage; Vertical Precise Measurement Cursor; Horizontal Precise Measurement Cursor; Rising/Falling Edge Trigger; Triggering Cursor; Triggering Sensitivity Cursor; Hold/Run Inbuilt Test Signal 10Hz~1MHz(1-2-5 stepping) Waveform Storage build-in 2Mbyte PC Connection Interface Connection through USB Recharging Method Recharging through USB interface Dimensions 105mm x 53mm x 8mm -
-
Arduino Mega 2560 Rev3 (Original)
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
Microcontroller ATmega2560 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limit) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 20 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz LED_BUILTIN 13 Length 101.52 mm Width 53.3 mm Weight 37 g Â
Warnings
The Mega 2560 has a resettable polyfuse that protects your computer’s USB ports from shorts and overcurrent. Although most computers provide their own internal protection, the fuse provides an extra layer of protection. If more than 500 mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.
-
LKR90.00LKR100.005VDC SPDT Relay 10A – THR SRD-05VDC-SL-C
LKR90.00LKR100.00
